Emulex LP982 Manual de usuario Pagina 92
- Pagina / 371
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Update Firmware
Prerequisites:
● The driver for Linux (including lputil) is installed properly.
● The firmware file has been downloaded to a local drive.
This procedure uses the lputil utility, which is installed with the driver.
Caution
If you are using lputil to update firmware on an
LP10000DC, LP10000, LP1050DC, LP1050 or LP9802DC
HBA, you must use lputil version 1.5a0 or later. For any
other HBA, you can use lputil version 1.4a4 or later.
Firmware versions differ between adapter versions. Make
sure you have downloaded the appropriate firmware for
your adapter.
Load Firmware
Caution
Do not interrupt this process or power down the system
until the process is complete.
1. Start the utility by entering the complete path to lputil. The path in the example
reflects the default installation path. If the installation path was modified, adjust the
command appropriately.
/usr/sbin/lpfc/lputil
2. From the Main menu, enter 3, Firmware Maintenance.
3. If prompted, choose the HBA that is being updated.
4. Enter 1, Load Firmware Image.
5. Enter the full path to the firmware file.
6. Enter 0 twice to exit the utility.
The new firmware is transferred to flash ROM.
If you are updating the firmware on a dual-channel HBA, repeat steps 3 through 5 to
update the firmware on the second port.
Emulex Documentation, Drivers and Software
92
- Version 7.1 1
- Table of Contents 1
- Supported Features 2
- New Features in this Release 3
- Known Issues 7
- Use HBAnyware 10
- Use lputilnt or lputil64 12
- Use lputil 13
- Use lp6dutil 15
- Driver Information 18
- ❍ LP8000 and LP8000DC 19
- ./ioctl-install 20
- Directory Structure 22
- ./ioctl-install --uninstall 24
- Installing the Driver Kit 25
- ./lpfc-install --uninstall 26
- ./lpfc-install 26
- Upgrading the Kernel 29
- Installing the Utilities 39
- Configurator 40
- Start HBAnyware for Linux 45
- The Toolbar 47
- The Discovery Tree 48
- Property Tabs 50
- Status Bar 50
- Using the CLI Client 51
- CLI Client Command Reference 51
- Start lputil 58
- Discover HBAs - Introduction 59
- Discover HBAs Using HBAnyware 60
- List Adapters using lputil 61
- Reset Adapter - Introduction 62
- Reset HBAs Using HBAnyware 63
- Reset Adapter Using lputil 64
- Display HBAs 67
- Display Local HBAs Only 68
- View Discovered Elements 69
- View Host Attributes 70
- View Fabric Attributes 72
- View Target Attributes 73
- View LUN Attributes 75
- View General HBA Attributes 77
- Link Status Area 78
- View Detailed HBA Attributes 79
- View Port Attributes 81
- View Port Statistics 83
- ● Assign AL_PA IDs 84
- Load Firmware Using HBAnyware 89
- Details tab 90
- Boot Bios Field Descriptions 91
- Update Firmware 92
- FC Boot 93
- Update BootBIOS 94
- Enable BootBIOS Message 95
- (lputil) 96
- Load EFIBoot Using HBAnyware 97
- Boot the EFI System 99
- Configuring the Driver 100
- Reset All Default Values 104
- ● Permanently (global) 105
- ● Temporary (global) 105
- ● Temporary (per adapter) 105
- Creating a New Ramdisk Image 109
- Set Up LUN Support 110
- Understand Device Numbering 113
- Download PCI Configuration 114
- To show persistent names: 122
- # devlabel status 122
- View Target Mapping 123
- Set Up Persistent Binding 124
- HBAnyware Security Overview 128
- /usr/sbin/hbanyware/ssc 129
- Create the ACG 130
- 5. Click OK or Apply 131
- Designate an MSC 132
- ACG Icons 134
- Add a Server to the ACG 137
- Delete a Server from the ACG 138
- Generate New Security Keys 141
- Configuration 142
- Access a Switch 143
- ASG Icons 144
- Create an ASG 146
- Reserved Indices - Examples 148
- Add a Server to an ASG 149
- Deleting an ASG 150
- Edit an ASG 152
- About Offline ASGs 154
- Backup Masters - Introduction 155
- Create a Backup Master 157
- Introduction 164
- Driver Install Fails 165
- ./stop_hbanyware 166
- Custom Built Kernel 171
- After Upgrading The Kernel 172
- Driver Uninstall Fails 174
- Cannot Install HBAnyware 176
- Run HBAnyware 182
- Cannot See Any HBAs 183
- Management Server 185
- SAN Management Workstation 186
- Does Not Have 186
- Cannot See New LUNs 187
- All Servers Are Not Displayed 190
- Cannot Add or Remove a Server 191
- Cannot Create a Backup Master 198
- Available 200
- Client Assigned" 205
- Unsecure System" 206
- Master Client System" 207
- Connect to the FC Network 208
- Were Offline 209
- ELS Events (0100 - 0199) 215
- Mailbox Events (0300 - 0399) 253
- ❍ Reduce the LUN size 342
- Link Events (1300 - 1399) 363
- SLI Events (1400 - 1499) 367
Relacionado con productos y manuales para Software Emulex LP982
Software Emulex LP21000 Manual de usuario
(274 paginas)
(274 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales