Emulex LightPulse LPe1105-M4 HBA Guía de instalación Pagina 73
- Pagina / 182
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation instructions for the Emulex v7.x-Series driver
73
Installing and Configuring the Linux Host with the Emulex Driver
VNX series or CLARiiON storage system as well as allow the SCSI
stack to scan up to 255 devices. The Unisphere/Navisphere Host
Agent requires that the disconnected LUN 0 be reported.
The DKMS RPM will install the Emulex driver as a module.
Note: After the driver installation, the system should be rebooted so that the
lpfc driver may be loaded through the newly created ramdisk.
1. Boot into the qualified and supported kernel into which the
driver will be installed. Ensure that the kernel sources and the gcc
compiler tools are installed.
2. Create a directory to which you will save the tar archive:
mkdir /home/emulex
3. Obtain the lpfc_2.4_dkms_kit-7.1.14-2.tar.gz from the
Emulex website as instructed under “Downloading the Emulex
v7.x-Series HBA driver for the v2.4.x kernel” on page 68.
Install the Emulex driver’s tar archive onto your system with the
following steps:
1. Uncompress and extract the source files from the tar archive:
cd /home/emulex
tar zxvf lpfc_2.4_dkms_kit-7.1.14-2.tar.gz
The initial uncompression will create a new directory and will
provide you with the following files within the new directory:
lpfc_2.4_driver_kit-7.1.14-4/
lpfc_2.4_driver_kit-7.1.14-4/dkms-2.0.4-1.noarch.rpm
lpfc_2.4_driver_kit-7.1.14-4/lpfc_2.4_dkms_kit-7.1.14-2.tar.gz
lpfc_2.4_driver_kit-7.1.14-4/lpfc_2.4_driver_kit-7.1.14-4
lpfc_2.4_driver_kit-7.1.14-4/lpfc_2.4_driver_kit-7.1.14-4.tar.gz
lpfc_2.4_driver_kit-7.1.14-4/lpfcdfcdkms-1.0.13-2.noarch.rpm
lpfc_2.4_driver_kit-7.1.14-4/lpfcdkms-7.1.14-2.noarch.rpm
lpfc_2.4_driver_kit-7.1.14-4/README
2. If you do not already have DKMS installed on your system, then
install the DKMS RPM contained within the newly created
directory. If DKMS is already installed on the system, then skip to
the next step to perform the Emulex driver installation.
rpm -ivh dkms-2.0.4-1.noarch.rpm
- -508-435-1000 1
- Contents 3
- Emulex Driver 4
- Chapter 8 Additional Notes 6
- ◆ Linux operating environment 9
- ◆ Emulex adapters and drivers 9
- Courier italic 11
- Introduction 13
- Purpose of this document 14
- Host connectivity 14
- Boot device support 15
- Installation Steps 19
- Linux distribution of choice 21
- Summary of installation steps 22
- Installing the adapter 24
- Adapter edge connectors 28
- PCI Express slots 29
- PCI Express slots aligned 29
- Installing and 31
- Configuring the BIOS 31
- Settings 31
- LP1102 Emulex banner 32
- Updating the boot BIOS 33
- LP6DUTIL.EXE) 37
- LP6DUTIL.EXE program file 37
- 7.x driver) 38
- Installing and 43
- Configuring the Linux 43
- Host with the Emulex 43
- SLES 9, SLES 10, and SLES 11 52
- /sys filesystem 58
- ...Restoring 83
- Cleaning up 86
- ./hbanyware 86
- * If PEMC owerPath 88
- ◆ Miracle Linux v4.0 92
- ◆ RedFlag DC Server 5.0 92
- 4 and RHEL 5” on page 91 93
- Updating the Adapter 97
- Firmware 97
- FCoE adapters 102
- Connecting to the 109
- Planning procedure 110
- Enabling persistent binding 111
- Connecting to the Storage 112
- Editing /etc/modules.conf 114
- Network Settings window 117
- Configuring a Boot 121
- Device on an EMC 121
- Storage Array 121
- Limitations 124
- /dev/sda by the Linux 125
- Preparing the host 128
- CLARiiON 136
- Emulex v7.x-Series driver 138
- Application Kit 141
- Do you have a driver disk 142
- Driver Update OK 143
- Upgrading the Linux kernel 145
- Additional Notes 147
- Rebooting the host 151
- HPQ server-specific note 155
- Block device file names 157
- Red Hat distributions 158
- SuSE distributions 158
- PowerPath examples 159
- Character device file names 159
- Echoing the /proc filesystem 163
- Rescanning the SCSI bus 164
- Special Instructions 167
- For example: 170
- 3. Reboot the host 170
- • For SuSE distributions use: 173
- Example: 173
- 4. Reboot the host 173
- 2.1 Intel Itanium systems 178
- 3.0 Intel Itanium systems 179
Relacionado con productos y manuales para Software Emulex LightPulse LPe1105-M4 HBA
Software Emulex LP21000 Manual de usuario
(274 paginas)
(274 paginas)
Promise Technology FastTrak S150 manuels
Manuels d'utilisation et guides de l'utilisateur pour Mise en réseau Promise Technology FastTrak S150.
Nous fournissons des manuels en pdf 1 Promise Technology FastTrak S150 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales