Emulex LP1005DC-CM2 Manual de usuario Pagina 43
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Driver for Linux - Configuration Section Page 37
• Tx Sequences - Fibre Channel sequences transmitted by this HBA port.
• Link Failures - the number of times the link failed. A link failure is a possible cause of a timeout.
• Loss of Signal - the number of times the signal was lost.
• Invalid Tx Words - the total number of invalid words transmitted by this HBA port.
• Ex Count Orig - the number of Fibre Channel exchanges originating on this port.
• LIP count - the number of loop initialization primitive (LIP) events that have occurred for the port.
This field is not supported if the topology is not arbitrated loop. Loop initialization consists of the
following:
• Temporarily suspend loop operations.
• Determine whether loop capable ports are connected to the loop.
• Assign AL_PA IDs.
• Provide notification of configuration changes and loop failures.
• Place loop ports in the "monitoring" state.
• NOS count - this statistic is currently not supported.
• Rx Frames - the number of Fibre Channel frames received by this HBA port.
• Rx Words - the number of Fibre Channel words received by this HBA port.
• Rx KB Count - the received kilobyte count by this HBA port.
• Rx Sequences - the number of Fibre Channel sequences received by this HBA port.
• Loss of Sync - the number of times loss of synchronization has occurred.
• Prim Seq Prot Errs - the primitive sequence protocol error count. This counter is incremented
whenever there is any type of protocol error.
• Invalid CRCs - the number of frames received that contain CRC failures.
• Ex Count Resp - the number of Fibre Channel exchange responses made by this port.
• Error Frames - the number of frames received with cyclic redundancy check (CRC) errors.
• Dumped Frames - this statistic is not currently supported.
• Seconds Since Last Reset - the number of seconds since the HBA was last reset.
- Emulex Driver and Utilities 1
- Installation 7
- Compatibility 8
- Known Issues 8
- Installing the Driver Kit 9
- Directory Structure 10
- Upgrading the Kernel 12
- Installing the Utilities 18
- Uninstalling the Utililities 19
- Configuration 20
- Examples of Modifications 21
- The Menu Bar 22
- The Toolbar 22
- The Toolbar Icon Definitions 23
- Sort and Display Icons 23
- The Discovery Tree 24
- Property Tabs 25
- Status Bar 25
- Start lputil 28
- HBA Tasks 29
- Discover HBAs Using lputil 30
- Sort HBA Information 31
- button 32
- Sort Local HBAs Using lputil 32
- View Discovered Elements 32
- View Host Attributes 33
- View Target Attributes 34
- View LUN Attributes 35
- View Fabric Attributes 37
- View General HBA Attributes 37
- Status Area Field Definitions 38
- View Detailed HBA Attributes 39
- View Port Information 40
- Port Field Definitions 41
- View Statistics 42
- View Firmware Information 44
- View Target Mapping 45
- View Driver Parameters 46
- Driver Parameter Tab Buttons 48
- ./stop_hbanyware 48
- Figure 20: The Main Menu 49
- Reset Adapters 50
- Reset the HBA Using lputil 51
- Update Firmware 52
- Prerequisites 53
- Procedure 53
- Update Firmware Using lputil 55
- Boot Code 56
- Load Boot Code using lputil 58
- Configure the Driver 61
- Reset All Default Values 64
- Set Up LUN Support 67
- Understand Device Numbering 68
- Download PCI Configuration 68
- The 'devlabel' Tool 72
- Set Up Persistent Binding 73
- Add Persistent Binding 74
- HBAnyware Security 76
- Access Control Groups 78
- ACG Icons 80
- Create the ACG 80
- Add a Server to the ACG 81
- Delete a Server from the ACG 82
- Generate New Security Keys 84
- Access a Switch 86
- Access Sub-Groups 87
- ASG Icons 88
- Create an ASG 88
- Reserved Indices - Examples 90
- Add a Server to an ASG 90
- Deleting an ASG 91
- Edit an ASG 91
- Backup Masters 93
- Create a Backup Master 95
- Troubleshooting 98
- Disable the rmserver process: 101
- Error Message Situations 105
- Introducton 108
- Message Group Masks 109
- Message Log Example 110
- ELS Events (0100 - 0199) 111
- Mailbox Events (0300 - 0399) 123
- LUN <num> 153
- Link Events (1300 - 1399) 159
- SLI Events (1400 - 1499) 160
Relacionado con productos y manuales para Software Emulex LP1005DC-CM2
Software Emulex LP9802DC Manual de usuario
(69 paginas)
(69 paginas)
Software Emulex LP10000ExDC Manual de usuario
(366 paginas)
(366 paginas)
Software Emulex LP982 Manual de usuario
(371 paginas)
(371 paginas)
Software Emulex LP21000 Manual de usuario
(274 paginas)
(274 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.161 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales