Emulex ONECONNECT OCE10102-F Guía de usuario

FUJITSU StorageETERNUS DXConfiguration Guide -Server Connection-(FCoE) for VMware® ESXDriver Settings for Non-Fujitsu Converged Network Adapter CardsP

The following shows an example of this.Host name Server#1IP Address 192.168.0.10Physical slotnameConverged Network Adaptercard WWNInstance name Physic

If multiple Converged Network Adapter cards are already installed in the server at the time of pur-chase, the one-to-one relationship between the WWN

2 Enter the number of the Converged Network Adapter card for which SAN Boot is to be set and press the[Enter] key.------------------------------------

4 Select "Enable" and press the [Enter] key.-------------------------------------------------------------------------------

6 Select "Configure Boot Devices" and press the [Enter] key.-------------------------------------------------------------------------------

8 A list of the WWPNs and recognized LUNs (as device names) of the connected ETERNUS DX400 series isdisplayed. Input the number of the device that is

11 Set the "Boot number". Select the boot device startup method (via WWPN or via DID), and change thesetting.Input "Boot this device vi

1.2.3 Installing VMware ESX•VMware ESX should be installed now if it has not yet been installed in the server. Refer to the followingURL for details.h

*1: Recommended value = 512 ¸ (number of FCoE ports that are connected to a single CA port) ¸number of LUNs(Round the result down)Use the value of &qu

1.2.4.2 For VMware vSphere 5.1 or 5.01 Record the module name for the Converged Network Adapter card that is loaded into VMware ESXi.The underlined po

This page is intentionally left blank.

Use the following command to change the setting values when the driver parameter name is"lpfcX_lun_queue_depth", the number of I/Os is "

In the following example, the number of ports is "two" since "4" and "5" (two underlined portions) aredisplayed as the S

Chapter 2 Setup Procedure for QLogic Converged NetworkAdapter CardsThis chapter describes how to set up the VMware ESX server and driver when connecti

Setting Up Converged Network Adapter Card DriverPerform the settings for the Converged Network Adapter card driver.•"2.2.5 Setting Up the Converg

2.2 Setting Up the Converged Network Adapter CardsThis section describes how to set up the server with the QLogic Converged Network Adapter cards desc

The procedure is as follows:1 Install the Converged Network Adapter card in the server.For the installation method, position (PCI bus slots), and note

7 Perform the BIOS settings for the Converged Network Adapter card.Check the parameter values in the [Adapter Settings] window against those in the fo

(2) Select the Converged Network Adapter card to be set (BIOS setting) in the [Select Host Adapter]window.The [Fast!UTIL Options] menu appears. Then p

4 Check the values for each parameter.Selectable Boot SettingsSelectable Boot:(Primary) Boot Port Name, Lun: Boot Port Name, Lun: Bo

8 Select [Reboot System] and press the [Enter] key.Exit Fast!UTILReboot SystemReturn to Fast!UTILThe server reboots.To return to the [Fast!UTIL] menu,

PrefaceThis manual briefly explains the operations that need to be performed by the user in order to connect anETERNUS DX to a server running VMware®

2.2.5 Setting Up the Converged Network Adapter Card DriverChange the parameters for the Converged Network Adapter card driver.2.2.5.1 For VMware vSphe

This option cannot be individually applied to each port on the Converged Network Adapter card.All ports on the target Converged Network Adapter card

When the value for this setting is changed, refer to "FUJITSU Storage ETERNUS DX ConfigurationGuide -Server Connection- (FCoE) for VMware® ESX&q

2 Check the default value for the Converged Network Adapter card.Specify the module name for the Converged Network Adapter card that you recorded in S

Appendix A WWN Instance Management Table for the Server(Blank)This table is used for setting up the Converged Network Adapter cards. Utilize this tabl

FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-(FCoE) for VMware® ESXDriver Settings for Non-Fujitsu Converged Network Adapter Card

The Contents and Structure of this ManualThis manual is composed of the following two chapters and an appendix.•"Chapter 1 Setup Procedure for Em

Table of ContentsChapter 1 Setup Procedure for Emulex Converged Network Adapter Cards 61.1 Workflow ...

Chapter 1 Setup Procedure for Emulex Converged NetworkAdapter CardsThis chapter describes how to set up the VMware ESX server and Converged Network Ad

Setting Up Converged Network Adapter Card DriverCheck the default setting values and number of ports for the Converged Network Adapter card, and setup

1.2 Setting Up the Converged Network Adapter CardsThis section describes how to set up the VMware ESX server for use with the Emulex Converged Network

3 Enter the number of the Converged Network Adapter card that is to be checked and press the [Enter]key.Example:--------------------------------------