Emulex 110 Guía de instalación Pagina 191
- Pagina / 240
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Manually installing the adapter driver — Advanced users
191
Miscellaneous Planning and Procedures
Note: Step 18 and Step 19 are only necessary for users using SCSIPort
drivers. STORPort users can skip these steps.
18. After the reboot is completed, install the EMLXApps Application
Kit included with the driver. To do this, expand the
setupapps.exe contained in the EMLXApps .zip file, and run
the setupapps.exe program. This install updates the Windows
installer to v2.0 and then installs three Emulex applications: the
Port driver configuration tool (ELXCFG.EXE), the mini-port driver
configuration tool (LPUTILNT.EXE), and the HBAnyware
Application. Follow the instructions during the Application Kit
installation and complete the installation.
19. For Windows 2000/Windows 2003 SCSIPort installations only,
run the ELXCFG.EXE tool and follow these procedures:
a. “Updating the shortcut” on page 203
b. “Changing the configuration” on page 205
Upgrading to Windows 2003 from Windows 2000
Note the following if upgrading to Windows 2003:
◆ Upgrading from Windows 2000 — The Windows 2000 drivers
may be preserved while upgrading to Windows 2003. These
SCSIPort drivers (including the native Windows 2003 SCSIPort
drivers) are not supported by EMC for Windows 2003. You
should obtain the correct Windows 2003 drivers (refer to
“Installation and configuration overview” on page 21) and
reinstall the drivers after the upgrade is complete.
◆ Currently, to upgrade from Windows 2000 to Windows 2003, you
must first uninstall PowerPath. After upgrading the host, you can
reinstall an approved Windows 2003 version. Please refer to the
EMC PowerPath documentation for further details.
You may wish to disconnect your storage during the Windows
upgrade, and reconnect it after the approved Windows 2003 drivers
are installed.
Note: Currently, EMC does not support upgrading Windows 2000 to
Windows 2008.
- Windows Environment 1
- Contents 3
- Chapter 3 Troubleshooting 5
- Title Page 13
- Installation and 19
- Configuration 19
- How this guide works 20
- Installing the adapter 22
- ◆ PCI-X 2.0 24
- ◆ PCI-Express 24
- Adapter edge connectors 25
- PCI Express slots 26
- CDC392a2.awc) 30
- Table 2 Firmware filenames 31
- LP6DUTIL main screen 34
- LP6DUTIL flash menu 35
- Selecting the adapter to load 36
- LP6DUTIL.EXE tool 36
- Change Boot BIOS State window 37
- Figure 11 Emulex banner 39
- Adapter configuration options 41
- Enabling/disabling an adapter 41
- Setting the PLOGI retry timer 42
- Saved boot devices 43
- Firmware boot manager menu 48
- Device mapping table 49
- Directory listing 50
- Current topology setting 57
- Figure 39 Targets 60
- Boot device identification 62
- — This can be 63
- Figure 58 Targets 75
- Existing partitions 84
- Windows Boot Manager 87
- Windows Setup screen 87
- Windows Install screen 88
- Windows 90
- Loading driver screen 91
- Browse for Folder screen 92
- A as shown in Figure 73 92
- Install Windows screen 95
- Limitations 97
- EMC support 97
- Emulex HBAnyware utility 98
- Pre-installation guidelines 99
- Installation complete 103
- AutoPilot installer program 104
- 5. Select Next to continue 105
- Topology selection 107
- Completing the installation 108
- Installer\reports 109
- HBAnyware: General tab 110
- HBAnyware: Firmware tab 111
- Adapter BIOS upgrade 113
- Adapter (CNA) procedures 117
- Device Manager 118
- HBAnyware utility 119
- Figure 98 121
- Maintenance tab 122
- Confirmation dialog box 123
- Firmware Download window 124
- Figure 104 Options 127
- CEE ta b 128
- Warning dialog box 129
- Start Download 130
- Progress bar 131
- Installation completed window 135
- AutoPilot Installer window 136
- Driver installation window 137
- Firmware tab 141
- Firmware file location 142
- Download Firmware dialog box 145
- CNA adapters 146
- Enable the adapter 149
- List of Saved Boot Devices 150
- Setting the primary boot LUN 151
- Selecting the boot method 154
- Reboot message 154
- OCe10102-IM iSCSI adapters 155
- Enable Boot Support 158
- Controller Static IP Address 159
- Adding iSCSI Target 161
- Channel adapter 169
- ElxSec Setup Wizard 172
- Config.bat 176
- Emulex NPIV solution 179
- Miscellaneous Planning 181
- Downloading the driver 183
- Installing the adapter driver 183
- EMC Support Matrix 184
- STORPort drivers 185
- A:\, for 190
- Blade server restrictions 193
- ELXCFG.EXE 195
- Changing the configuration 205
- Version 1.41a2 options 207
- Preconfigured settings 208
- Maximum Number of LUNs 208
- MSCS with tape devices 209
- Emulex configuration tool 212
- Set the adapter FC-AL Loop ID 218
- Troubleshooting 221
- Basic troubleshooting steps 222
- Volume sizes 227
- Host after the rebooted 230
- Understanding queue depth 231
- Known issues 233
- Problems and solutions 235
- Problem 5 236
- Problem 6 236
- Problem 7 236
- Problem 8 236
- Third-Party Software 239
- Emulex HBAnyware 240
Relacionado con productos y manuales para Redes Emulex 110
Redes Emulex LP11002 HBA Manual de usuario
(31 paginas)
(31 paginas)
Redes Emulex 110 Manual de usuario
(119 paginas)
(119 paginas)
Redes Emulex ONECONNECT OCE10102-F Guía de usuario
(36 paginas)
(36 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales