Emulex 110 Guía de instalación Pagina 197
- Pagina / 240
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using the Emulex configuration tool
197
Miscellaneous Planning and Procedures
◆ EMC fabric with EMC PowerPath/ATF
(InitLinkFlags=0x00000002 (fabric, auto-link speed),
WaitReady=10, LinkDown=10)
ELXCFG.EXE v1.41a4 enables adapter settings to connect to a
Symmetrix, VNX series, or CLARiiON from the same host while
using the same adapter. This version is distributed separately, and is
labeled EMC universal configuration tool for Symmetrix, VNX
series, or CLARiiON. To enable custom EMC array configuration
settings, a user must start the utility with a command line option of --
emc. Refer to “Updating the shortcut” on page 203.
The EMC array auto-configuration settings are no longer presented
automatically as the configuration tool will no longer auto-detect if
an EMC array is present on the fabric. If the -- emc option is enabled,
the configuration tool will automatically mask some of the checkbox
selections, and will present a four-choice EMC array
auto-configuration dialog box under the Configuration-Set menu.
These settings noted below are modified for the global driver defaults
and apply to all adapters in the system. This enables the same
adapter to connect to a Symmetrix, VNX serie, or CLARiiON from the
same host while using the same adapter.
The EMC choices will reset the link-speed to Auto. Manually
modifying the link-speed later will no longer remove the checkbox
from the EMC auto-configuration choices.
All adapter global settings are Emulex defaults, with the exception of
the following:
◆ MaximumQueueDepth=32, MaximumLun=255,
UniqueNodeWwns=1,
ShowUnknowns=1, MultipleScsiClaims=1, BrokenRscn=1,
NameServerDelay=800ms, Windows Disk Class Driver
Timeout=60s
◆ EMC arbitrated loop without EMC PowerPath/ATF
(InitLinkFlags=0x00000000 (arbitrated loop, auto-link speed),
WaitReady=45, LinkDown=45)
◆ EMC arbitrated loop with EMC PowerPath/ATF
(InitLinkFlags=0x00000000 (arbitrated loop, auto-link speed),
WaitReady=10, LinkDown=10)
◆ EMC fabric without EMC PowerPath/ATF
(InitLinkFlags=0x00000002 (fabric, auto-link speed)
WaitReady=45, LinkDown=45)
- Windows Environment 1
- Contents 3
- Chapter 3 Troubleshooting 5
- Title Page 13
- Installation and 19
- Configuration 19
- How this guide works 20
- Installing the adapter 22
- ◆ PCI-X 2.0 24
- ◆ PCI-Express 24
- Adapter edge connectors 25
- PCI Express slots 26
- CDC392a2.awc) 30
- Table 2 Firmware filenames 31
- LP6DUTIL main screen 34
- LP6DUTIL flash menu 35
- Selecting the adapter to load 36
- LP6DUTIL.EXE tool 36
- Change Boot BIOS State window 37
- Figure 11 Emulex banner 39
- Adapter configuration options 41
- Enabling/disabling an adapter 41
- Setting the PLOGI retry timer 42
- Saved boot devices 43
- Firmware boot manager menu 48
- Device mapping table 49
- Directory listing 50
- Current topology setting 57
- Figure 39 Targets 60
- Boot device identification 62
- — This can be 63
- Figure 58 Targets 75
- Existing partitions 84
- Windows Boot Manager 87
- Windows Setup screen 87
- Windows Install screen 88
- Windows 90
- Loading driver screen 91
- Browse for Folder screen 92
- A as shown in Figure 73 92
- Install Windows screen 95
- Limitations 97
- EMC support 97
- Emulex HBAnyware utility 98
- Pre-installation guidelines 99
- Installation complete 103
- AutoPilot installer program 104
- 5. Select Next to continue 105
- Topology selection 107
- Completing the installation 108
- Installer\reports 109
- HBAnyware: General tab 110
- HBAnyware: Firmware tab 111
- Adapter BIOS upgrade 113
- Adapter (CNA) procedures 117
- Device Manager 118
- HBAnyware utility 119
- Figure 98 121
- Maintenance tab 122
- Confirmation dialog box 123
- Firmware Download window 124
- Figure 104 Options 127
- CEE ta b 128
- Warning dialog box 129
- Start Download 130
- Progress bar 131
- Installation completed window 135
- AutoPilot Installer window 136
- Driver installation window 137
- Firmware tab 141
- Firmware file location 142
- Download Firmware dialog box 145
- CNA adapters 146
- Enable the adapter 149
- List of Saved Boot Devices 150
- Setting the primary boot LUN 151
- Selecting the boot method 154
- Reboot message 154
- OCe10102-IM iSCSI adapters 155
- Enable Boot Support 158
- Controller Static IP Address 159
- Adding iSCSI Target 161
- Channel adapter 169
- ElxSec Setup Wizard 172
- Config.bat 176
- Emulex NPIV solution 179
- Miscellaneous Planning 181
- Downloading the driver 183
- Installing the adapter driver 183
- EMC Support Matrix 184
- STORPort drivers 185
- A:\, for 190
- Blade server restrictions 193
- ELXCFG.EXE 195
- Changing the configuration 205
- Version 1.41a2 options 207
- Preconfigured settings 208
- Maximum Number of LUNs 208
- MSCS with tape devices 209
- Emulex configuration tool 212
- Set the adapter FC-AL Loop ID 218
- Troubleshooting 221
- Basic troubleshooting steps 222
- Volume sizes 227
- Host after the rebooted 230
- Understanding queue depth 231
- Known issues 233
- Problems and solutions 235
- Problem 5 236
- Problem 6 236
- Problem 7 236
- Problem 8 236
- Third-Party Software 239
- Emulex HBAnyware 240
Relacionado con productos y manuales para Redes Emulex 110
Redes Emulex LP11002 HBA Manual de usuario
(31 paginas)
(31 paginas)
Redes Emulex 110 Manual de usuario
(119 paginas)
(119 paginas)
Redes Emulex ONECONNECT OCE10102-F Guía de usuario
(36 paginas)
(36 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales